Toyota Prius ABS Replacement Service in Islamabad

Toyota Prius ABS Replacement, Do Not Repair

September 23, 2021
By Atif Rashid
In Blog
Tags ABS, Prius, Toyota

3388
0

Toyota Prius ABS Replacement, Do Not Repair

Toyota Prius ABS Warning

Your Toyota Prius ABS system uses a system of sensors to determine wheel speed when braking. The antilock brake system runs through the ABS module. This module physically controls the anti-lock brake system If it becomes damaged, and can no longer control all four brakes, the Anti-lock Braking System (ABS) light will activate. Typically, corrosion is the most common reason why the module fails.

Modern automobiles are well-acquaint with the anti-lock braking system (ABS). When a car is subjected to dangerous braking, this system maintains control and directional steadiness. When one or more tires begin to lose traction, the car can travel in any direction it wishes, including completely sideways. According to research, managing the rotating speed of each tire in a vehicle with an ABS system can minimize the chance of a car accident by 18%.

A sensor that measures the speed of the wheels It is use to adjust the wheel’s revolving speed and located near the wheel. This data is transferred to the computer module, which collects data from all four wheel sensors. If the computer detects one or more wheels rotating slower than the rest, it will instruct the controller to drop the brake line pressure, which the pump will then maintain to let the wheel to resume rolling. As a result, if the system is turned on, the brake pedal may shake.

Prius ABS C1251

The Toyota Prius ABS C1251 light and the Traction light can turn on due to any problem with the braking system. Since most of Hybrid vehicles use regenerative braking to store electricity, any problem with ABS can cause a decline in the efficiency of the vehicle.

If you hear any hissing noise then be careful with your car’s brakes. This usually represents a failing unit with a leaking accumulator. Although it depends a lot on the DTC,s stored in the car, we recommend a professional scan tool. Improper fitting of transaxle assembly can cause failure in this system as well. This service involves the replacement of a unit but is refer to as an ABS repair service.

In contrast to previous automobiles, which had a Check Engine Light, a fault with the ABS system causes the ABS Light to illuminate in a yellow tint. If you’re experiencing this issue, you’ll require Toyota Prius ABS module replacement in Islamabad, Pakistan, and Fixmycar.pk is the finest in the business.

C1256 Toyota Prius

If you’re encountering a C1256 diagnostic trouble code (DTC) on your Toyota Prius, it’s important to understand its significance and potential implications. The C1256 DTC specifically relates to a problem with the ABS actuator motor circuit, which is responsible for controlling the Anti-Lock Braking System (ABS) in your vehicle. When this code appears, it indicates that there is an issue with the ABS actuator motor circuit, which could lead to compromised braking performance and safety concerns. To resolve this problem, it’s advisable to consult a qualified technician who can diagnose the root cause and perform the necessary repairs or replacements. By addressing the C1256 DTC promptly, you can ensure the optimal functioning of your Toyota Prius’s braking system, promoting a safe and reliable driving experience.

Toyota Prius ABS Unit Replacement Service in Islamabad

Relearning and matching of Toyota Prius ABS C1251 and C1256 units is necessary. This service can also be avail in case the traction control light has lit up. We also recommend a brake oil flush with this service so that the ABS unit can give a long life. Toyota Prius, Aqua and newer radar variants are available with us. Our techs perfectly match the ABS units with other on board electronics.

If you have an ABS warning light on, what should you do? Don’t be concerned! Fixmycar.pk offers Toyota Prius ABS Module Replacement Service in Islamabad, Pakistan. The fault might occur at any point during the ABS braking system’s operation, and the warning light will illuminate. In reality, the ABS light will remain on until the underlying problem is resolved. The warning light usually informs the driver that the safety system is no longer operational.

Contact us at m: 03312227989
Whatsapp our specialists now!

The brakes are control by the Brake Control Module (BCM), rather than the BCM regulating the pressure produce by the driver, as is the case with most braking systems. The purpose for this is so that the Hybrid control module and the BCM can work together. Simply put, when the brake pedal pressed, the Hybrid Control Module and the BCM assess and negotiate information about the driver’s intentions in order to satisfy the driver’s expectations. The end result is a mix of regenerative braking and hydraulic system application.

Hydraulic Control Unit

The system appears to be standard, however there is no hydraulic connection between the master cylinder and the brake calipers in normal operation. Instead, a hydraulic pump generates the pressure need to activate the brakes. The pressure at the master cylinder and the brake calipers is monitor via sensors. The brake hydraulic module has several sensors. Fault codes will be generate if there is an abnormality between these sensors.

How it works

The master cylinder isolation valves closed when the system is turn on, the stroke sensor solenoid valve is open, and the rear brake linear valves V8 and V10 are close. When the driver applies the brakes, the BCM gets information regarding speed and location from the master cylinder stroke sensor, as well as pressure sensors 1 and 2 on the master cylinder. The stroke simulator piston travels under pressure to provide the driver with the same feel as a traditional system while also allowing the master cylinder to stroke. The BCM evaluates this information and determines a braking technique.

There may be no hydraulic pressure supply to the calipers while braking at speeds above 10 km/h, and all braking is done by regeneration (the drag of the big motor/generator in the gearbox as it charges the battery). The regenerative and hydraulic brake applications will share the increase braking demand. The Controller Area Network used to communicate between the Hybrid ECU and the BCM (CAN).

Controlling the linear valves allows hydraulic brakes to be apply. Pressure-apply valves V3, V4, V5, and V6 are pressure-apply valves, whereas pressure-release valves V7, V8, V9, and V10 are pressure-release valves. The linear valves are control by a Pulse Width Modulated Current (PWM), which allows for extremely accurate pressure control in the braking calipers. The apply valves are open, allowing pressure to develop in the calipers. The pressure vented to the master cylinder when the release valve is open. The calliper pressure and wheel speed are both monitor and compare to data in the BCM. This enables the braking effect to be tailor to the driver’s needs.

Fault Codes

Brake pad replacement on the 2004-09 Prius does not require any special tools. However when the brake pedal is press for the first time to bring the brake pads into touch with the brake disc, error codes ‘C134x Hydraulic System xxx Malfunction’ may be produce. This is due to the fact that the BCM does not foresee a large pressure spike in the caliper. The codes can be remove manually at the EOBD socket or with an appropriate scan tool.

The hydraulics on the brake system may be bled without any special equipment, although it’s preferable to use the scan-tool. The hydraulic module must be initialize whenever it is remove or change; this procedure allows the system to determine the linear valves’ properties.

Brake Bleeding System

The hydraulic module’s valves revert to their default position when the ignition is switch off for more than two minutes. The master cylinder cutoff solenoids have now been remove, allowing brake fluid to flow to the front brakes. The two ABS relays are remove to prevent the system from becoming activate. To bleed the front brakes, first pump the master cylinder to build up pressure in the system, then release the bleed nipple to let the fluid out. The pipes leading to and from the master cylinder and the stroke simulator are bled properly when the front brakes are bled this way.

After replacing the two relays and turning on the ignition, the rear brakes may be bled. G-Scan will come in handy here. Choose ‘bleed rear left’ or ‘bleed rear right’ from the menu and follow the prompts. Alternatively, the rear calipers can bled using accumulator pressure, although this requires extreme caution and will result in fault codes that must be clear.

Brake pad replacement is a straightforward procedure. When the relays are remove, a clean path from the rear calipers to reservoir and from front calipers to master cylinder is form. During piston retraction, Toyota does not advocate clamping the brake hose and venting the caliper at the bleed nipple.

Note: the following is not a complete set of instructions on brake bleeding, it’s to demonstrate what is happening in the hydraulic system during the process. Remember you should always follow vehicle manufacturer’s instructions.

Users’ Guide to the ABS Pump

When buying an ABS (anti-locking brake system) pump to replace your old one, make sure the part numbers line up to ensure it’s the right one for your vehicle. Get it correctly the first time – You don’t want to buy the wrong one and then have to start looking for the proper one all over again.

Because the ABS pump is an electrical component, testing it may be challenging, and the best way to test it is using diagnostic tools. If the ABS is malfunctioning, it should display a fault code that helps you to pinpoint the source of the problem. If the ABS light on your dashboard remains lighted, there is a problem with the ABS unit.

How does an ABS Pump work?

By keeping the brakes from locking up and avoiding skidding, the anti-lock braking system guarantees that the wheels are constantly in tractive contact when driving. The ABS pump is made up of an ECU that monitors the speed of each wheel’s rotation and a hydraulic unit / pump that applies braking pressure. When the ECU detects that one of the wheels is turning faster than the others, the valves inside the brake lines boost the hydraulic pressure on that wheel’s brakes, slowing it down. If the wheel is travelling slowly, the pressure will be reduced in order to accelerate it. There are three settings for the valve in the brake lines as follows:

The valve is open in the first position, allowing the brake master cylinder to deliver pressure straight to the brakes without any pressure fluctuations.
The valve will seal the lines in the second position. Because the brake master cylinder is unable to provide any pressure to the brakes, the pressure will not rise if the driver applies additional pressure to the brake pedal.
The valve will levitate the pressure on the brakes at the third position.

The most typical issue with the vales is that they can get clogged, making them unable to open, close, or lower the pressure on the brakes.

Clearing the DTC (Diagnostic Trouble Code)

The ABS/VSC errors cannot be remove by disconnecting the negative battery cable. A scan tool can be use to clear codes. ABS codes can be be obtain as blink codes and clear using an OBD2 connection. Between pins 4 and 13 on the 16-pin OBD2 socket, a Special Service Tool, or SST is insert. The ABS/VSC light will flash when the ignition is turn on. All ABS/VSC codes will be clear if the brake pedal is apply eight times in five seconds.

Follow Us